Did she get longer?
No idea. But if she gets as big as Tonka, I might have to put a leash on her, and take her everywhere. She might get mad though.
Don’t have a Pretty Hairy Cock, not a chicken. And also, my cock doesn’t have hair on it. Around it.
That might be a bummer, if somebody has hair all over their dick, including where the piss comes out.
Then they’d have a Pretty Smelly Cock.
I need to go to bed, before I pass out.
But I’m still looking for a display to use with my Raspberry Pi 5. Going to move the Orange Pi Zero to where the Pi 5 is. And put the Pi 5 in a lunchbox briefcase.
Too much thinking to make what I want exactly, a portable Pi. Also, 3D printing is a pain in the ass, the reason I got rid of it.
Not paying $300+ for one either.
It can fit 12″ or so in there, just how many some people like. But do they like it 12″ and skinny?
15.6″ is only $90. But it’s too damn big. It just won’t fit. It’s too damn long.
18.5″ is apparently $60. I think it’s a cheap Chinese brand. But I need smaller.
Sure is hard to find a small display, without being bareback. That is the board is exposed on the back of it. Touch that to metal, and it’ll probably get fried.
Just the bareback screens are cheap, but you apparently need a 3D printer to secure them. Nobody wants to sell them ready to go, for a little more.
Might almost be the same size as my laptop. Not exactly what I wanted. Oh well. Better then my shitty ass phone.
If I was willing to get the Pi 5 out of it’s case, it might be cheaper. Or take the top off. And put a screen on it. Not sure I can.
No idea how to securely attach all the crap. Will ask somebody about that.
It’ll be ugly, but the 3D printed thing on Etsy would have been ugly too. Maybe smaller. But ugly. Now I get even more ugly.
To get Pi 5 out of case, might require cutting the case. It’s tight as fuck. Also, it needs a case. Therefore, it needs a case designed for a specific NVMe adapter. Pain in the ass, if you don’t know how to make 3D models, and you don’t want a 3D printer.
Apparently 5″ isn’t the right size. You either have to get smaller or bigger.
The smaller cheaper one of that brand on Amazon, has the board bareback.
And that other one, must be some old model or something.
And I’m probably going to just get junk anyways. Does Adafruit sell everything you need including the enclosure or case or display frame, whatever the fuck it’s called.
And that guide on learning, you need a 3D printer, and to solder.
There’s this, but no touch screen. And expensive.
But it might not be junk. I like Adafruit. How do you power that? Can my USB battery power it?
Might just have to give up the damn touch part. Didn’t want to buy a different keyboard. Or a mouse. Wanted to just touch the damn display.
Or just use a damn terminal and no GUI.
Might be able to find a non touch cheaper display, that isn’t junk. Still won’t be as good.
As on the bottom of Adafruit, says woman owned.
The Trump tax likely made a lot of stuff on Adafruit out of stock.
Also the touch screens on the cheap ones, might be junk.
Can it fit a full size keyboard in the thing I put? Cause there’s the Raspberry Pi 500.
And then I can spend $300 or more. Or maybe I shouldn’t. Cause then I’ll have nothing.
That thing probably uses too much power anyways. Too bad a CRT won’t fit in it.
It’s around $60 for the display + HDMI driver board. But then I need an enclosure. And might also need another battery, or different battery.
Jerry rigging might be the way to go. Can’t cheaply print Aluminum. Damn, not big enough for a 7 incher.
SmartiPi might have something. But instead of a Pi, can I use a driver board? And plug the other Pi into it.
Or you know, get some Aluminum sheets, and screws, and cut it somehow. And do it the harder and probably more expensive way.
What about wood? Too expensive.
Panel Mount – 7.0″ TFT that might be what I need.
How about a metal one?
How much is a laser cutter? Wood might work just fine. Got wood?
Seeing how much to get something printed. Might be the cheapest way. What a pain in the ass.
No regret getting rid of printer though, too much work. And I’d have to print it over and over again.
ABS or SLS Nylon PA12? Is the Nylon some kind of metal. Around $30 for that.
Would suck if it doesn’t work though.
But I don’t want to get it from Florida. I want it closer. And don’t want to pay $100+.
About $30 if I order from makexyz.com. There appears to be at least one printer person in my state as well. But what about the driver board? Where am I going to put that?
Hmm SunFounder on Amazon. Mount thing on Etsy. No need to take a massive chance on 3D printing something with zero comments.
And might not have needed the 3D print. Oh well. It’ll have double protection, it comes with a backplate too apparently.
Got to send money to somebody later to buy the display though. Unless I decide to look on eBay or something for it.